Skip to main content

Tested Printers

Here is a list of printers that have been tested with the software. If you have a printer that is not listed here, please open an issue or a pull request with the settings you used or contact us on Discord.

Zjiang ZJ-5890K Thermal Printer​

  • Printer Width: 384
  • Printer Type:
    • Raw USB Printing: Endpoint=0416:5011:01
    • Windows Direct Printing: Select Printer Name (Setup or install Chinese Driver)
    • CUPS: Select Printer Name (Setup)
  • Explicit Initialization: Off (or On when Direct USB Printing is used)
  • Force Standard Mode: Off
  • Cut After Printing: Off

Notes​

A lot of cheap 58mm printers you will find on Amazon and other shops are rebranded versions of this Printer. If your printer looks the same or is a generic 58mm printer try the above settings.

Zjiang ZJ-8330 Thermal Printer​

  • Printer Width: 576
  • Printer Type:
    • Raw USB Printing: Endpoint=0416:5011:03
    • Windows Direct Printing: Select Printer Name (Setup or install Chinese Driver)
    • CUPS: Select Printer Name (Setup)
  • Explicit Initialization: Off (or On when Raw USB Printing is used)
  • Force Standard Mode: On
  • Cut After Printing: On / Off

Metapace T-1​

  • Printer Width: 504
  • Printer Type: Serial
  • Endpoint: COM3:57600_N81_2
    • On Windows: COM3 needs to be changed to the COM port that the printer is registered
    • On Unix: COM3 should be replaced with /dev/tty.XXXXXX or something similar of the device
    • Warning: Old serial printer tend to have small buffer. The _2 indicates that a wait of 2 seconds will occur before each data chunk will be sent to the printer. If the printer doesn't finish printing try to increase this value! It seems on Windows a 0 works but on Unix systems a 2 second delay is needed.
  • Explicit Initialization: On
  • Force Standard Mode: On
  • Cut After Printing: On / Off

Notes​

A cheap DE-9 RS232-to-USB, DB-25 to DE-9 Adapter and DE-9 Null-Modem will be needed to connect this serial printer to your PC.

Connection: Printer → DB-25 to DE-9 → DE-9 Null-Modem → DE-9 RS232-to-USB → PC

BIXOLON SRP-350plusIII​

  • Printer Width: 504
  • Printer Type: Serial
  • Printer Type:
    • Windows Direct Printing: Select Printer Name (Setup)
    • Serial: Follow Metapace T-1 notes above
  • Explicit Initialization: On
  • Force Standard Mode: On

RONGTA 80 mm​

  • Printer Width: 576
  • Printer Type:
    • Raw USB Printing: Untested
    • Windows Direct Printing: Untested (Setup)
    • CUPS: Select Printer Name (Setup)
  • Explicit Initialization: Off / On (on Windows)
  • Force Standard Mode: Off / On (on Windows)
  • Cut After Printing: On / Off

MUNBYN ITPP047 80 mm​

  • Printer Width: 576
  • Printer Type:
    • Raw USB Printing: Untested
    • Windows Direct Printing: Tested (Setup)
    • CUPS: Untested (Setup)
  • Explicit Initialization: Off
  • Force Standard Mode: Off
  • Cut After Printing: On / Off

MUNBYN IMP001 58 mm​

  • Printer Width: 384
  • Printer Type:
    • Raw USB Printing: Untested
    • Windows Direct Printing: Tested (Setup)
    • CUPS: Untested (Setup)
  • Explicit Initialization: Off
  • Force Standard Mode: Off
  • Cut After Printing: On / Off

TSP100 Star Printer​

  • Printer Width: 509 (3 inch paper), 360 (2 inch paper)
  • Printer Type:
    • Windows Direct Printing: Select Printer Name (More info below)
  • Explicit Initialization: Off
  • Force Standard Mode: Off
  • Cut After Printing: On

Notes​

Only Windows Driver Available. You need to download and install the driver and follow the following guide to enable ESC/POS mode.

GOOJPRT MTP-3F 80mm​

  • Printer Width: 576
  • Printer Type:
    • Raw USB Printing: Untested
    • Windows Direct Printing: Untested
    • CUPS: Untested
  • Explicit Initialization: Unknown
  • Force Standard Mode: Unknown
  • Cut After Printing: On / Off

Epson TM-M30II​

  • Printer Width: 576
  • Printer Type:
    • Raw USB Printing: Untested
    • Windows Direct Printing: Untested
    • CUPS: Select Printer Name (Setup)
  • Explicit Initialization: Unknown
  • Force Standard Mode: Unknown
  • Cut After Printing: On / Off

sam4s GCUBE-102D​

  • Printer Width: 576
  • Printer Type:
    • Raw USB Printing: Endpoint=1c8a:3a39:01
    • Windows Direct Printing: Select Printer Name (Setup) (untested but should work)
    • CUPS: Select Printer Name (Setup) (untested but should work)
    • Serial: Worked with USB Serial Adapter + Null-Modem
  • Explicit Initialization: Off (or On when Raw USB Printing is used)
  • Force Standard Mode: On
  • Cut After Printing: On / Off

Notes​

There is a android NFC app that can be used to configure the printer. This is needed to set the printer to ESC/POS mode and 203 DPI.